Operating InstructionsEmitting electronicsfor VEGASON 64, 65, 66Ultrasonic
213Fig. 8: Position of the screws and locking ring on the example of the plastichousing1 Screw check angle2 Screw locking ring3 Locking ring2 Open the
Proceed as follows:1 Loosen the Torx screws on the housing socket with thesuitable key T152 Remove the previous emitting electronics from the flangeada
123Fig. 11: Mounting the new emitting electronics1 Emitting electronics2 Torx screws T15 (4 pcs.)3 Flange adapter2 Plug the new emitting electronics o
312Fig. 12: Dismounting the previous emitting electronics1 Emitting electronics with adapter for transducer tube2 Terminal screws (2 pcs.)3 Transducer
51234Fig. 13: Mounting the new emitting electronics1 Emitting electronics with adapter for transducer tube2 Terminal screws (2 pcs.)3 Groove for locki
4.6 Mounting steps version C/DDanger:The individual wires of the transducer cable have a voltage ofapprox. 70 V during operation (see chapter "Mo
12 3Fig. 15: Mounting the new emitting electronics1 Emitting electronics with socket2 Plug connector3 Connection piece swivelling holder or transducer
8 Screw the housing cover back onThe emitting electronics is exchanged.As a rule, the exchange of the emitting electronics must bedocumented internall
5 Setup5.1 SetupThe setupis carried out according to the operating instructionsmanual of the respective sensor.18 Emitting electronics - for VEGASON 6
6 Maintain6.1 Instrument repairIf a repair is necessary, please proceed as follows:You can download a return form (23 KB) from the Internet onour home
Contents1 About this document1.1 Function .. . . . . . . . . . . . . . . . . . . . . . . . . . . .31.2 Target group . . . . . . . . . . . . . . . . .
7 Dismounting7.1 Dismounting stepsTakenote of chapters "Mounting" and "Connecting to powersupply" and carry out the listed steps i
8 Supplement8.1 TechnicaldataTechnical dataare stated in the operating instructions manual of the appropriate sensor.Emitting electronics - for VEGASO
22 Emitting electronics - for VEGASON 64, 65, 66Supplement30205-EN-070510
Emitting electronics - for VEGASON 64, 65, 66 23Supplement30205-EN-070510
VEGA Grieshaber KGAm Hohenstein 11377761 SchiltachGermanyPhone +49 7836 50-0Fax +49 7836 50-201E-mail: [email protected] 9001All statem
1 About this document1.1 FunctionThisoperating instructions manual has all the information youneed for quick mounting and setup of a replacement modul
2 For your safety2.1 Authorised personnelAlloperations described in this operating instructions manualmust be carried out only by trained specialist p
3 Product description3.1 ConfigurationThe scope of delivery encompasses:l Emitting electronicsl 4 pcs. Torx screwssize 15 (with version A)l Documentati
3.3 Packaging, transport and storageYour instrument was protected by packaging during transport.Its capacity to handle normal loads during transport i
4 Mounting4.1 General instructionsIfthe emitting electronics is defective, it can be replaced by theuser.If there is no emitting electronics available
Electronics module SN-SE.64C is suitable for VEGASON 64,65, 66 version C and D.The following tools are required for dismounting and subse-quent re-mou
1 Switch off power supply2 Remove the housing cover from the electronics compart-ment, or from the connection compartment of the Aludouble chamber hous
Comments to this Manuals